Licensed & Insured Independent Pros
Every call goes to an independent contractor carrying insurance and licensing where required. Ask for proof before work starts.
Water trickling through a wall crack, a pipe entry or a window well every time it rains? Call now and we'll connect you with an independent, licensed and insured contractor in Gallipolis who pinpoints the leak and seals it, without selling you a whole-basement system you don't need.

A lot of basement water problems are just one or two leaks. If water shows up in one predictable place, like a crack below a window, the gap around a sewer pipe or a corner under a downspout, you're dealing with a point leak. Those are usually faster and far less expensive to fix than a whole-basement problem.
The trick is finding the true entry point. Water can enter at a crack eight feet away and travel along the cove joint before it puddles where you notice it. It can run down inside a hollow block core and appear at the floor. Tracing comes first, because patching the wrong spot only redirects the water.
Local pros use meters, thermal cameras and hose testing to confirm the source before quoting.

The visible puddle is rarely the whole story. A careful contractor starts at the wet spot and works outward, checking the wall above it, the cove joint on both sides and any pipes, windows or tie-rods nearby. A pin moisture meter shows how far the dampness spreads inside the concrete, which often points straight at the source.
Thermal imaging helps on finished walls. Wet areas behind drywall show up as cooler patches, so the contractor can see the path water takes without cutting into the wall. For block foundations, a borescope through a small hole can show whether the cores are holding water.
If needed, a hose test outside, one section at a time, confirms it. Water runs against one section of the outside wall for a set time while someone watches inside. Then the next section. It takes patience, but it pinpoints the exact entry point.
With the entry point confirmed, the fix is usually fast and targeted. If tracing shows water coming in at many points along the cove joint, the honest answer may be a drainage system for that section, and a good contractor will tell you so instead of injecting cracks that aren't the real problem.
Timing matters too. A crack that drips a little each storm keeps feeding moisture into the wall, the framing and anything stored nearby. Over a season or two, that can mean rusted tie-rods, rotting sill plates or mold behind finished drywall. Point repairs are at their cheapest when the leak is new and the surrounding material is still sound, so it's worth calling after the first drip rather than the tenth.

Finding and sealing one leak properly takes the right approach.
Every call goes to an independent contractor carrying insurance and licensing where required. Ask for proof before work starts.
Most point repairs are quoted per crack, per penetration or per window, in writing, before work begins.
Local contractors often seal a crack the same day they inspect it.
Low-pressure injection pumps, surface ports, hydrophobic polyurethane resin, structural epoxy, thermal cameras and pin moisture meters.
Each leak type has a fix that matches it.

Expanding polyurethane injected under low pressure fills the crack front to back and stays flexible.
Epoxy restores strength across dry cracks, chosen when the wall needs bonding as well as sealing.
Gaps around pipes are cleared and sealed with flexible or expanding materials that won't crack as the pipe shifts.
Window wells without working drains fill like buckets. Repairs can include a new drain to the footing, gravel base, a fitted cover and resealing the window frame itself.
Localized floor seepage can be sealed, but widespread cove joint leaks usually call for drain tile in that section.
Rusting form ties let water in at regular intervals. Each one is cleaned and sealed individually.
Point repairs are the right answer when the water truly enters in one or two places. But sometimes tracing reveals a pattern: seepage at the cove joint along most of a wall, several cracks leaking at once, or water rising through the slab in more than one spot. That usually means the soil around the foundation is saturated and hydrostatic pressure is pushing everywhere, not just at one weak point.
In that case, injecting one crack at a time can become an expensive cycle, because each repair just moves the pressure to the next weak spot. An honest contractor will tell you when you've reached that point and explain the options, from a partial drain tile run along one wall to exterior grading changes that reduce the water load. You still decide. The aim is to spend your money on the fix that actually stops the leaks, not on a series of patches that each work for one season.
It also helps to keep a simple log. Note the date, the weather and where water showed up each time it happens. Three or four entries give a contractor a clear picture of whether you have one stubborn leak or a pattern that points to a bigger drainage problem, and it often shortens the inspection.
Simple, fast and focused on the actual leak.
Call +1-866-476-1348 and describe exactly where you see water and what the weather was doing. Photos of the spot help a lot.
A local independent contractor schedules a visit, often the same or next day for active leaks.
The contractor traces the leak with moisture readings, thermal imaging or a hose test, then quotes the repair in writing.
The leak is sealed, often in a single visit, and the contractor explains how to check it after the next rain and what the warranty covers.
One call gets a local independent pro out to trace and seal it.
Call +1-866-476-1348We had one crack that dripped every rainstorm. Another company quoted a full drain system. The contractor from this line injected the crack in about two hours and it hasn't leaked since.
Ruth K., Gallipolis
The leak showed up in the middle of the wall, but he found it was actually coming in around the sewer pipe and running along the joint. Sealed the pipe and done.
Marcus J., Gallipolis
Our window well filled up like a bathtub. They installed a drain, gravel and a cover and resealed the window frame. Problem gone.
Elena T., Gallipolis
Weekend call, weekend fix. Quick, clean and reasonably priced.
Jim W., Gallipolis
Yes, if the water is truly entering at that one crack. Injection seals the crack through the full wall thickness. If water is coming in at many points, a broader solution may make more sense, and a good contractor will say so.
Because water moves along joints and inside walls before you see it. That's why tracing comes before sealing.
It's good for quick plugs but rigid. For moving cracks, flexible polyurethane injection usually lasts longer.
A single crack injection is usually a few hundred dollars, with pipe penetrations and window wells in a similar range depending on access. The contractor will quote your specific repair in writing.
Surface patches tend to fail under water pressure. Professional injection fills the crack through the whole wall.
Call the contractor first, since most warranty their injection work. If it's a new leak elsewhere, that may point to a bigger drainage issue.
We connect homeowners throughout Gallipolis and nearby towns with independent contractors who specialize in targeted basement leak repair. Poured, block and stone foundations are all covered.
Check the area list below or just call.
